在建筑工地施工現場中，必要要安裝臨邊防護欄，以防止落物傷人或施工人員在工作時因意外墜落而造成事故。在臨邊護欄的生產和安裝過程中，需要達到很多的要求才能保證其起到相應的作用，下面我們一起來看臨邊護欄生產以及安裝要求。

In the construction site of the construction site, it is necessary to install the edge guard to prevent falling objects from hurting people or the construction personnel from causing safety accidents due to accidental fall during work. In the production and installation process of edge guardrails, many requirements need to be met to ensure that they play a corresponding role. Let's look at the production and installation requirements of edge guardrails.

臨邊護欄生產要求：

Production requirements for edge guardrails:

臨邊護欄需要使用的原材料為鋼管，經過焊接生產加工而成，鋼管的表面應平直光滑，不硬出現裂痕、分層、毛刺、結疤、壓痕、錯位、硬彎及深劃痕等產品質量問題。

The raw material used for the edge fence is high-quality steel pipe, which is welded, produced and processed. The surface of the steel pipe should be straight and smooth, and there should be no crack, delamination, burr, scar, indentation, dislocation, hard bend, deep scratch and other product quality problems.

原材料鋼管在投入生產前需要對其壁厚警醒抽查檢驗，為了保證符合生產要求，抽檢比例不得低于30%，對于壁厚下差超過10%的鋼管不可投入生產。如在抽查鋼管的過程中，發現不合格比例高于30%時應加大抽查力度。

The wall thickness of raw steel pipes needs to be vigilant and spot checked before they are put into production. In order to ensure that they meet the production requirements, the sampling proportion shall not be less than 30%. Steel pipes with a wall thickness difference of more than 10% cannot be put into production. For example, in the process of spot check of steel pipes, if the unqualified proportion is found to be higher than 30%, the spot check shall be strengthened.

為了保證臨邊護欄的使用壽命以及防腐性能，鋼管以及扣件的表面必須進行防銹處理。

In order to ensure the service life and anti-corrosion performance of edge guardrails, the surface of steel pipes and fasteners must be treated with rust prevention.

扣件在使用前要進行檢查篩選，不可以出現變形、裂痕的情況，螺栓不可出現劃絲。

The fasteners shall be checked and screened before use, and there shall be no deformation and cracks, and the bolts shall not be scratched.

臨邊護欄安裝要求：

Installation requirements of edge guardrail:

在工地施工現場中，工作人員進場必須佩戴帽，臨邊護欄施工現場堆放材料需按平面布置圖要求歸位，臨邊護欄的各個工作點都需要設置有針對性的警示標識，施工現場要制定抽水措施，防止出現積水造成事故。

In the construction site, the staff must wear safety helmets when entering the construction site. The materials stacked on the construction site of the edge guardrail should be put back in place according to the requirements of the layout plan. Targeted safety warning signs should be set at all work points of the edge guardrail. Pumping measures should be developed on the construction site to prevent water accumulation from causing safety accidents.

臨邊護欄的高度要高于1.2米，寬度1.5-2m，底部需要設置踢腳板，高度15-20cm。在外部需加掛網，并設置有針對性的警示標識。

The height of the edge guardrail should be higher than 1.2m, and the width should be 1.5-2m. A skirting board should be set at the bottom, with a height of 15-20cm. Safety nets shall be hung externally and targeted safety warning signs shall be set.

在安裝時一定要保證網片和立柱鏈接牢靠，網面安裝需平整，無明顯翹曲和凹凸現象。

During installation, ensure that the mesh and column are firmly connected, and the mesh surface installation needs to be flat without obvious warpage and concave convex phenomenon.

臨邊護欄生產以及安裝要求詳解內容就到這里了，希望給您好的幫助，當然您在購買時候也要提前做好準備，購買到好的產品，更多事項就來網站http://www.siemax-cx.com咨詢吧！

That's all for the detailed explanation of the production and installation requirements of the edge guardrail. I hope you can help me. Of course, you should be prepared in advance when you buy a good product. If you buy a good product, please come to the website for more information http://www.siemax-cx.com Consult!